• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Recent content by __caligula2

  1. C

    Good Reasonably Inexpensive Waterblock that Fits Socket A and A64 Sockets

    Well not actually, the mcw6000 is 3/8 but the 6002 is all 1/2inch you want it to be!
  2. C

    cleaning your heatsink?

    Clean it with alcohol or as I do with ether, which you can get from any drugstore
  3. C

    New casemod, first time water cooling.

    Since it is obvious you're new to all the watercooling, my suggestion to you is that you read alot about it. Read some tutorials, browse through the forums of the sites I will give you through. To answer your questions, yes you can oc a x800. And yes it will bring you very noticeable results...
  4. C

    Apple gets wet

    Well that's just the strategy of apple, making something fancy and very attractive that people can show off with. And people prepared to spend 3000$ on such a system DO want to have complete silence at this speed.
  5. C

    Where to Mount Pump? Picture to help you help me :)

    You anyway get to deal with gravity because water has to come up again ;) And now it has to suck which isn't the best for a pump.
  6. C

    holy c0w 51 degrees idle

    Maybe the heatsink is not properly installed... And btw bios temps is always under load. If your cpu is reading from the mobo probe then you should lower that reading by 10°C
  7. C

    Cracked WhiteWater, Cont'd.

    Looks very nice and fine orkan! Didn't your case temps increase too much with the hot air being blown in?
  8. C

    Vdimm mod for gigabyte 8pe667 ultra

    Nobody?
  9. C

    Vdimm mod for gigabyte 8pe667 ultra

    Hello all, After one year owning this board I decided to step up one step and to voltmod this board. I already found out which chip regulates the vcore (HIP6301) but I don't know How to change the voltage for the ddr. Is there anybody who knows which chip is responsible for regulating ddr...
  10. C

    226W Pelt - Custom DD Kit problems

    I agree with zer0signal667. If the loop is no problem, then the ps could be it. Check with volt and amp meter. You should at least get half a centimeter of frost on that stuff without load! If that doesn't cut it, resolder the wires untill inside the pelt how I did it. You'll have to scrape...
  11. C

    North bridge cooler for Abit NF-S V2

    Very nice, weapon. I'm building something similar to this with an old dangerden chipset cooler of 2 generations back. Transforming it into a pelt cooler. Luckily my brother now works in a technical school wich facilitates the build of my pelt wb.
  12. C

    226W Pelt - Custom DD Kit problems

    Sounds like your setup can't cool the pelt because you don't even get frost as I understood. With 226W you should get -35° C without load. Did you put thermal paste on both sides of the pelt? Check if water can flow freely through your loop. The cables of the pelt shouldn't feel warm, it's...
  13. C

    Mobo Vdimm mod?

    Go to Xtrmesystems and look there for your mod, if you can't find it here probably it has never been done or can't be done...
  14. C

    Distance between moboholes

    Yes of course I might do that but with a margin of error obviously. I would want to find a scheme like intel's socket 478 specification pdf.
  15. C

    Distance between moboholes

    Hello, I'm building a waterblock for my chipset, can anyone tell me the distance between the holes or even give me the link to a scheme, it would even be better! Thanks
See more
Back
Top